Mash Compliant logo
You are here:

MASH Compliance for Road Safety Barriers

Full-scale crash testing, the six MASH test levels, and why compliance testing is adopted for barriers installed in Australia.

THE STANDARD

Evaluation Through Full-Scale Crash Testing

The Manual for Assessing Safety Hardware (MASH), published by the American Association of State Highway and Transportation Officials (AASHTO) is a performance standard used for the evaluation of roadside safety hardware. MASH is an update to and supersedes the National Cooperative Highway Research Program (NCHRP) Report 350. The introduction of MASH reflects changes to the vehicle fleet and the increasing sale of heavier, high-centre-of gravity vehicles. In addition, MASH considers real-life crash impact scenarios and adopts a more rigorous assessment when compared to the superseded NCHRP Report 350 standard.

MASH is recognised globally by road safety engineers and is the basis of crash testing as nominated by Australian Standard AS/NZS 3845.1:2015. Furthermore safety barrier products evaluated by the Austroads Safety Barrier Assessment Panel (ASBAP) must be crash tested in accordance with MASH guidelines.

All RamShield® road safety barriers are full-scale crash tested in accordance with MASH. The crash testing assessment evaluates barrier behaviour, vehicle containment and occupant risk. A longitudinal safety barrier should safely contain and redirect the errant vehicle within allowable occupant ridedown decelerations.

The MASH matrix adopted for each performance level is designed to represent the worst practical condition. The test vehicle mass, impact speed, impact angle, barrier configuration and point of impact represents the most extreme real-life impact condition placing maximum load on the barrier system. The impact severity or kinetic energy of the crash test impact is unlikely to be exceeded during a real life crash accident.

The MASH specification presents uniform guidelines for the crash testing of both permanent and temporary highway safety features and recommended evaluation criteria to assess test results. Guidelines are also presented for the in-service evaluation of safety barriers.

Ideally, the roadside would be clear of all hazards allowing a motorist that leaves the roadway to recover and safely return to the travelled way. However, removing all hazards is not practical and an appropriate safety barrier system that reduces the consequences of a vehicle leaving the roadway is the preferred treatment option.

Our range of crash barrier systems have been developed to meet the needs of the Australian motorist and designer. For more information please review our RamShield story.

Mash Compliance vehicle

Our Range

Guardrail Barriers

Guardrail barriers are classified as longitudinal road safety barriers designed to safely contain and redirect errant vehicles away from roadside hazards. They comprise a steel beam guardrail, either w-beam or thriebeam, supported by yielding steel posts.

Guardrail End Terminals

Guardrail end terminals are designed to anchor the longitudinal guardrail barrier and reduce the severity of an impact occurring at the end of the system. The MSKT end terminal is an energy-absorbing terminal, evaluated to MASH TL3, that features a slotted anchor rail and impact head that reduces occupant risk.

Bridge and Culvert Barriers

Bridge and culvert barriers are a specific range of longitudinal barriers designed for installation along the edge of an elevated concrete deck. Our designs include conventional post and rail systems and a freespanning system capable of spanning up to 16m between abutment posts.

TEST MATRIX

MASH Test Vehicles

The test vehicles nominated in the MASH specification are selected to represent the majority of vehicle types using Australian roadways. The small car crash test primarily evaluates occupant risk and the potential for the vehicle to snag the barrier. The heavy vehicle impacts are designed to evaluate the capacity of the barrier system and safe vehicle containment and redirection.

Test Vehicle

Test Vehicle Mass (kg)

1100C (passenger car)

1,100

2270P (pick-up truck)

2,270

10000S (single-unit truck)

10,000

36000V (tractor-van trailer)

36,000

36000T (tractor-tank trailer)

36,000

MASH Test Levels

Longitudinal barriers may be tested to six test levels. A test level is defined by impact conditions (speed and angle of approach) and the type of test vehicle (ranging in size from a small car to a fully loaded tractor-trailer truck). The selection of an appropriate test level considers the speed of the roadway, traffic volume and heavy vehicle usage.

Although different barriers may comply with the same test level, they may have different applications when considering dynamic deflection, working width or occupant accelerations.

Test Level

Test Reference

Vehicle

Impact Speed (km/h)

Impact Angle (degrees)

Impact Severity (kJ)

1

1-10

1-11

1100C

2270P

50

50

25

25

18.9

39.1

2

2-10

2-11

1100C

2270P

70

70

25

25

37.1

76.7

3

3-10

3-11

1100C

2270P

100

100

25

25

75.8

156.4

4

4-10

4-11

4-12

1100C

2270P

10000S

100

100

90

25

25

15

75.8

156.4

209.3

5

5-10

5-11

5-12

1100C

2270P

36000V

100

100

80

25

25

15

75.8

156.4

595.4

6

6-10

6-11

6-12

1100C

2270P

36000T

100

100

80

25

25

15

75.8

156.4

595.4

The most commonly specified test level is MASH TL3, recognising that 95 % of Australian vehicles fall within this range. The specification of MASH TL3 represents an economical barrier solution allowing more metres of barrier to be installed per Australian public dollar.

Frequently Asked Questions

The American Association of State Highway and Transportation Officials (AASHTO) issues guidance on the design and installation of roadside and safety hardware, and is the publisher of the Manual for Assessing Safety Hardware (MASH).

MASH provides a set of uniform guidelines for the evaluation of permanent and temporary roadside barriers. MASH is adopted by Road Agencies allowing them to evaluate the performance of different barrier types to meet the needs of their respective jurisdictions.

MASH is an update to and supersedes NCHRP Report 350. MASH considers changes to the vehicle fleet which continues to shift towards heavier vehicles with a higher centre-of-gravity.

MASH has made several changes including a heavier passenger car, pick-up truck and rigid truck; a higher impact speed for the rigid truck; a higher impact angle for the passenger car; and changes to the evaluation criteria.

The 1100 kg weight of the small passenger car test vehicle was selected to represent approximately the 2nd percentile of passenger type vehicles, i.e., only two percent of vehicles weigh less than the specified test weight.

The weight of the pick-up truck was increased from 2000 kg to 2270 kg. The heavier pick-up is representative of the large numbers of dual cab utility vehicles sold within the USA and in Australia.

The MASH standard was developed to represent real-life impact conditions and therefore recognises that heavy trucks typically travel at lower speeds when compared to passenger vehicles. In addition, heavy trucks typically occupy the slow lane of a roadway, reducing the offset distance to the roadside barrier which reduces the maximum attainable impact angle.

Each test level nominates several vehicle impact conditions. It is a requirement that each crash test is performed. Each test level requires passenger impacts representing the majority of road users and ensuring that barriers designed for heavy tuck impacts provide safe containment of the smaller vehicles and comply with occupant deceleration guidelines.

When selecting the MASH test parameters, such as the test vehicle, impact speed and angle combination, point of impact, test matrix, etc., every effort was made to specify the worst, or most critical, conditions. In a real-life crash it is unlikely that the combination of speed and impact angle will exceed the MASH test requirements.

Yes. MASH is the basis of crash testing as nominated by Australian Standard AS/NZS 3845.1:2015. In addition the Austroads Safety Barrier Assessment Panel (ASBAP) requires that roadside barriers are crash tested in accordance with MASH. It is a requirement that safety barriers undergo ASBAP evaluation prior to acceptance by Australian state road agencies.

No. Road safety barriers that are not MASH compliant have been reclassified as Legacy status by state road agencies. This allows the existing barriers to remain in use for their service life. However once a legacy barrier is significantly damaged or the roadway undergoes a major upgrade, these barriers should be replaced with MASH compliant systems.