RamShield Edge guardrail logo
You are here:

RamShield® Edge Barrier

MASH TL4 Compliance on Weak Soil Embankments

RamShield® Edge Protection Barrier

MASH Test Level 4 Compliance for Weak Soil Embankments

MASH TL4 Compliant

RamShield® Edge is an engineered variation of RamShield® High Containment, facilitating installation on the hinge point of weak batter slopes. Following installation of the C-posts, a steel pin is driven at approximately 45 degrees back into the road formation and secures the C-post at ground level. The pins prevent below ground movement of the C-posts during a vehicle collision, replicating flat terrain performance, and providing safe vehicle containment and redirection.

RamShield® Edge has been crash tested in accordance with MASH TL3 and TL4 of the Manual for Assessing Safety Hardware (MASH) when installed on the hinge point of a 1:1 weak soil embankment. RamShield® Edge is recommended for acceptance by the Austroads Safety Barrier Assessment Panel (ASBAP) and approved for use by Australian state road agencies.

The anchoring of each C-post back into the road formation creates a restraint mechanism that is independent of the soil properties and embankment geometry behind the post.

Crash Test Evaluation

RamShield Edge crash test results by vehicle type

Barrier configuration

Vehicle

Mass

Impact Speed

Impact Angle

Impact Energy

Dynamic Deflection

Posts at 2 m centreson the hinge point of a 1:1 weak soil embankment
2,270kilograms
25degrees
156.4kilojoules
0.9metres
Posts at 2 m centreson the hinge point of a 1:1 weak soil embankment
10,000kilograms
15degrees
209.3kilojoules
1.6metres

Installation

RamShield Edge system specifications

Post Type

Standard Post Spacing

Post Embedment

Beam Type

System Height

Driven post with pins 2.0 m 890 mm Thrie-beam 1,000 mm

Key Features

  • MASH TL3 and TL4 compliant, crash tested on the hinge point of a 1:1 weak soil embankment
  • Below-ground pins prevent below ground movement of the posts
  • Anchoring in front of the post ensures the restraint is not dependent upon soil properties behind the post
  • Pins may be reused following design impacts
  • Replicates flat terrain crash test performance
  • Standard post spacing: 2 m centres
  • Recommended for acceptance by ASBAP

Video

Downloads

Frequently Asked Questions

RamShield® Edge is a variant of RamShield® High Containment that features pins secured to each post below ground. The pins are anchored in front of the barrier and prevent below-ground movement of the posts during a vehicle collision. RamShield® Edge is designed for use when the barrier is installed on the hinge point of weak soil embankments where there is insufficient lateral support behind each post.

RamShield® Edge when installed on the hinge point of a 1:1 weak soil embankment has been full-scale crash tested in accordance with MASH TL3 and TL4 demonstrating containment of a 2270 kg pickup truck travelling at 100 km/h and 25 degrees and a 10,000 kg rigid truck travelling at 90 km/h and 15 degrees.

Following installation of the C-posts, the restraining pins are driven at approximately 45 degrees back into the road formation. The pins are driven to ground level and are then secured with a clamp to each C-post.

A mobile test rig, known as THOR, can perform a dynamic impact to ensure the restraining pin prevents below ground movement causing the post to yield by bending proximate to ground level.

The installation of a barrier adjacent to a weak soil embankment often provides insufficient lateral support. During a collision the posts can push through the embankment causing the errant vehicle to override the barrier. Conventional treatment options of increasing post embedment depth and/or reducing post spacing provide limited improvement in lateral support and are dependent upon the soil properties behind each post.

By comparison, RamShield® Edge anchors each post back into the road formation and is therefore not dependent upon soil properties behind each post. RamShield® Edge is a crash tested, engineered solution that replicates flat terrain performance.

RamShield® Edge has been crash tested to meet MASH TL3 and TL4 when positioned on the hinge point of a 1:1 weak soil embankment.

The use of longer posts relies upon the soil strength behind the post to provide sufficient lateral support. Installations adjacent to weak soil embankments with longer posts are highly unlikely to provide similar lateral support to a flat terrain installation.

The installation of RamShield® Edge can avoid expensive road formation widening or embankment stabilisation required for the installation of conventional barriers.

A thrie-beam system provides numerous advantages when compared to a w-beam system for installation adjacent to a steep embankment. A thrie-beam system provides a higher rail mounting height, a wider lateral catching area and deeper post embedment.

The Manual for Assessing Safety Hardware presents uniform guidelines for the crash test assessment of temporary and permanent road safety hardware.

MAKE AN ENQUIRY