MASH TL4 Compliant
You are here:

MASH TL4

Higher capacity barrier systems designed to withstand high energy vehicle impacts.

TEST CRITERIA

MASH TL4 Containment for Heavy Vehicle Routes

The crash test requirements of MASH Test Level (TL) 4 exceeds MASH TL3. The MASH TL4 impact criteria includes the MASH TL3 impacts with an additional crash test undertaken with a 10,000 kg rigid truck travelling at 90 km/h and 15 degrees.

Test

Vehicle

Impact Speed

Impact Angle

Impact Severity

4-10

1100C passenger car

100 km/h

25 degrees

75.8 kJ

4-11

2270P pick-up truck

100 km/h

25 degrees

156.4 kJ

4-12

10000S single-unit truck

90 km/h

15 degrees

209.3 kJ

The MASH TL4 vehicle represent a single-unit box truck with a higher centre of gravity when compared to passenger vehicles. The box truck impact increases the lateral load on the barrier system and introduces the potential for the vehicle to rollover or vault the barrier during impact. MASH TL4 is typically specified on roadways where a higher number of heavy vehicles are encountered.

The specification of MASH TL4 is typically limited to longitudinal barriers. The upper limit for the crash test evaluation of guardrail end terminals is MASH TL3. Please refer to our MASH compliance for further information.

Our Range

RamShield High Containment

The increased system stiffness of RamShield High Containment when compared to w-beam guardrail combined with the higher mounting height of the thriebeam guardrail provides safe containment and redirection of single-unit truck vehicles.

CrocGuard Culvert Barrier

Spanning up to 16 m between abutment posts, the unique composite design of CrocGuard provides safe vehicle containment and redirection when installed on the edge of bridge or culvert structure.

RamShield Edge

RamShield Edge is a variant of RamShield High Containment featuring below-ground pins that improve the lateral strength of the C-posts. Crash tested to MASH TL4 when installed on the batter hinge point of a 1:1 weak soil embankment.

VGAN 400 Bridge Barrier

The triple rail design of VGAN 400 is designed to withstand heavy vehicle impacts when installed on the edge of bridges. Manufactured from aluminium providing a lightweight barrier system and superior corrosion resistance.

Frequently Asked Questions

Three crash tests. An 1,100 kg passenger car at 100 km/h and 25 degrees, a 2,270 kg pick-up truck at 100 km/h and 25 degrees, and a 10,000 kg rigid truck at 90 km/h and 15 degrees.

The MASH TL4 test matrix requires three (3) full scale crash tests. An 1100 kg passenger car travelling at 100 km/h and 25 degrees; a 2270 kg pickup truck travelling at 100 and 25 degrees; and a 10,000 kg rigid truck travelling at 90 km/h and 15 degrees.

Vehicle occupants are typically more vulnerable in a small car. The small car impact ensures that barriers systems that are stiffened to withstand the high-energy rigid truck impact still satisfy the occupant risk guidelines for small car occupants.

No. MASH TL4 is typically limited to the assessment of longitudinal barriers. The upper performance limit for guardrail end terminals is MASH TL3.

Due to the requirement to withstand an impact from the 10,000 kg rigid truck, MASH TL4 barriers are typically stiffer than TL3 systems and the height of the system is increased to contain the higher centre-of-gravity rigid truck.

The working width is measured from the point on the barrier closest to the traffic lane to the furthest position of the vehicle during the test impact. It combines the dynamic deflection of the barrier system and any vehicle roll.

Dynamic deflection is the maximum displacement of the barrier recorded during a full-scale crash test. Designers should consider dynamic deflection when shielding steep embankments, culverts and other hazards that are located close to the groundline. Working width combines the dynamic deflection of the barrier and any vehicle roll. Therefore working width is considered when shielding bridge piers, power poles and other fixed hazards that typically extend above the top of the barrier system.

The 10,000 kg truck typically exhibits vehicle roll during full-scale crash testing. Therefore working width is measured to the top of the cargo box.

MASH does not nominate a specific cargo box height for the 10,000 kg rigid truck, therefore the height at which the working width was measured should be provided by the barrier system proprietor.